Sliding glass doors
Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Entry doors
Impact garage doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateWhy Enterprise Homeowners Choose CGI Windows & Doors
We provide independent CGI windows & doors service in Enterprise, NV, repairing, retrofitting, and installing CGI vinyl windows and doors with quality parts that fit them. What sets our CGI work apart is diagnostic depth: we know the specific failure patterns CGI units develop in Mojave Desert heat, and we help you tell a repairable unit from one that’s genuinely at end of life. We’re an independent provider, not CGI-authorized, and we don’t claim any manufacturer endorsement. If your CGI window is fogging, dragging, or refusing to latch, call (877) 558-4821. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Enterprise is full of CGI. The master-planned subdivisions on the valley’s west side, Southern Highlands and Rhodes Ranch among them, were built mostly in the 1990s through the 2020s, and vinyl units like CGI’s ended up in a large share of those tract homes. That means a lot of CGI windows across Enterprise are now twenty to twenty-five years old and running into the end of builder-grade service life.
Why Trust Enterprise Windows & Doors for Your CGI Windows & Doors?
Our technicians have up to 11 years of experience, and a good portion of that has been spent on CGI vinyl windows and doors in Enterprise’s newer and mid-era subdivisions. We know the hardware. We know the glass packages. We know what a CGI single-hung sash does when its frame has been heat-cycled through fifteen summers.
More to the point, we know it as an independent provider. We’re not CGI-authorized, factory-trained, or certified by the manufacturer. We work on CGI products because we’ve diagnosed their quirks firsthand, service call after service call. That independence matters for you: nothing pushes us toward a replacement when a repair will honestly do, and nothing pulls us toward a specific CGI series because we’re obligated to move inventory.
We repair and install CGI equipment with quality parts that fit it. Where the original hardware profile is still supported we source OEM or OEM-equivalent rollers, sash locks, keepers, and glazing seals. Where it isn’t, we spec a matched aftermarket component that holds up in the same conditions. That approach keeps CGI service warranty-safe: we work within the unit’s original design intent, avoid cutting into sealed assemblies that shouldn’t be opened, and document what we changed so you have a record if a warranty question ever comes up.
We’re a windows-and-doors specialist. Every conversation here is about openings, glazing, and hardware, not roofing or siding or remodeling. That focus is why CGI service is something we can actually speak to with depth.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Common CGI Windows & Doors Problems We Fix in Enterprise
Enterprise sits at the foot of the Spring Mountains, and the combination of intense afternoon sun and spring wind does a specific kind of damage to builder-grade vinyl. These are the CGI problems we see repeatedly.
- Vinyl sash and frame warping. Sustained 100°F+ summer heat softens PVC over time, and a CGI sash that has been baked on a southwest-facing wall will start to bow. You feel it before you see it: the lock gets hard to throw, the sash won’t seat flush, and the weatherstripping at the frame leaves a gap that whistles in a spring wind. Left alone, a warped sash wears its own weatherseal and pulls the lock hardware out of alignment with the keeper.
- Seal failure and desiccation in dual-pane IGUs. The fogging and cloudiness in a CGI insulated glass unit isn’t cosmetic. The perimeter seal has degraded under UV exposure and thermal cycling, moisture has entered the airspace, and the unit has lost its insulating value. In Enterprise, it tends to hit southern and western elevations first, because that high-desert sun bakes the edges of builder-grade units before the rest of the window shows any wear. Seal failure is a glass problem, not a frame problem, and it’s often repairable on its own.
- Roller and track wear on CGI horizontal sliders. Sliding vinyl windows in Enterprise collect grit from spring dust storms, and that grit grinds into aluminum tracks. The rollers flat-spot, the track pits and oxidizes, and the sash starts to drag, jump, or come off the track entirely. This is the most common CGI hardware failure we’re called out for in the valley.
- Frames out of square from settling and thermal movement. Stucco-and-frame tract homes settle, and thermal expansion pulls CGI frames out of square a fraction at a time. A single-hung sash that used to slide now binds through its travel, and the lock hardware misses its keeper by an eighth of an inch. Re-squaring the opening and adjusting hardware is the usual answer, not a new window.
- UV-degraded door seals and gaskets. CGI vinyl sliding patio doors and entry-door systems live with a hard life in Enterprise: sun-baked gaskets, dried-out weatherstripping, and multipoint hardware that stops engaging cleanly when the frame has moved. If you can see daylight along the door edge or the multipoint handle won’t turn home, the seal or the frame alignment is the culprit.
That last point connects to a broader pattern in Enterprise. This isn’t northern Nevada, where the window problems are driven by freeze-thaw cycles. Here the enemy is sun, dust, and dry heat. The dual-pane seals fail and the door gaskets bake, and the wall the window sits on matters as much as the window itself. Meanwhile, many HOAs in Southern Highlands and Rhodes Ranch require window and door replacements to match the original framing color and style, so a replacement plan has to account for that before anyone orders product.
CGI Parts & Our Repair-vs-Replace Approach
The honest answer for most single failed CGI units is repair. Glass, hardware, and seals are replaceable, and a fogged IGU gets measured and swapped rather than the whole window getting pulled. We use OEM or OEM-equivalent CGI replacement hardware – rollers, sash locks, keepers, glazing seals – where the profile is still supported. We don’t stock or carry genuine CGI parts, and we’re not a CGI dealer; we source what fits your unit and what lasts in Enterprise’s climate.
Replacement becomes the right call when the failure is structural. Widespread frame warping across a twenty-year-old CGI window wall in a tract home, with multiple sashes bowing and weatherseals failing, usually means you’re chasing repairs that won’t hold. That’s a good time to look at full-frame replacement.
Two specific things tell us which side of the line you’re on. First, is the failure isolated or systemic? One fogged unit on a window wall of ten is a glass job. Ten of ten is a window-wall decision. Second, is the frame still plumb? If the sashes bind and the lock hardware misses the keeper across multiple units, the frame has moved and repairs won’t stabilize it.
We’ll put that assessment in writing with a free estimate before any work starts. Call (877) 558-4821 to set that up.
Our CGI Service Process – Step by Step
Here’s how a CGI job usually goes with us, from first call to closed file.
- 1
Diagnosis. We start with the failure pattern, not the product. Is the sash binding through its travel or just at the lock? Is the fogging in the airspace or on the surface? Is the roller flat-spotted or the track bent? Each answer points to a different repair.
- 2
Repair or install. For a repair, the sash comes out, worn hardware comes off, the track gets cleaned and lubricated, and any out-of-square frame gets brought back to tolerance. For glass, the IGU is measured precisely and swapped as a unit. For a full install, we set the new CGI unit square, flash and seal the rough opening properly, and match the frame color and style against the HOA requirement before we order.
- 3
Test. Every job gets a live test at the window or door: operate the sash through full travel, throw the lock and check the keeper engagement, run water or a light check around the perimeter, and confirm the weatherseal tightens against the frame through a full cycle.
- 4
Warranty and documentation. We hand you a written record of parts replaced and work performed. Warranty terms come directly from us in that written form, not from CGI. We’ll explain exactly what’s covered and for how long.
Our technicians have up to 11 years of experience running this sequence on CGI units across Las Vegas valley subdivisions, and they don’t rush the test step. That’s where most callbacks come from.
See the difference
Before
After
Before
After
Before
AfterCGI Products We Service & Install in Enterprise
We work on the CGI vinyl window and door lines that actually show up in Southern Nevada housing stock.
- Single & Double Hung Windows. CGI vinyl single-hung and double-hung units, especially the builder-grade windows common in tract homes. Our work covers sash realignment, lock and keeper adjustment, weatherseal replacement, and glass swap.
- Horizontal Roller & Sliding Impact Windows. CGI vinyl horizontal rollers and impact-rated sliding assemblies. We replace rollers and track hardware, re-seat sashes, and service impact-rated dual-pane laminated glass assemblies.
- Energy-Efficient Upgrade. Where an aging CGI unit is staying in place but the glass has failed, we can move to an energy-efficient glazing package matched to the frame.
We’re an independent service provider. We’re not a CGI dealer, and we don’t carry or stock CGI inventory. We service and install CGI products, and we’ll tell you honestly which CGI unit makes sense for your opening.
We Also Service These Brands
Because our lineup runs across eight brands – PGT, CGI, CWS, ES Windows, ECO Window Systems, Mr-Glass, Therma-Tru, and ViewLux – we can match the product to the project instead of the project to whatever a single-brand dealer happens to have on hand. That matters for the performance call: impact-rated products live on one side of the portfolio, energy-efficient products on another, and door systems from Therma-Tru stand on their own. For a CGI owner in Enterprise, this means when CGI turns out not to be the right fit for one opening in the house, we can say so and quote an alternative without sending you to another company.
FAQs – CGI Windows & Doors Service in Enterprise
No. We’re an independent provider serving Enterprise, NV. We are not CGI-authorized, not factory-trained, and not certified by the manufacturer. We service CGI products because we’ve worked on them extensively and know their failure patterns in this climate. Call (877) 558-4821 for a free estimate.
Not necessarily. The most common cause is a frame that’s slightly out of square from settling and thermal movement. When it happens, the sash binds through its travel, the lock hardware misaligns with the keeper, and the weatherseal leaves a gap. Re-squaring the opening and adjusting the hardware usually corrects it, and replacing a couple of hardware pieces resolves it outright. Frame warping bad enough to require replacement shows as multiple sashes bowed on the same wall. Call (877) 558-4821 for a free assessment.
Yes, in most cases. Fogging in a CGI dual-pane unit is a seal failure inside the insulated glass unit, which is a separate part from the sash frame. If the sash and frame are still square, we measure the unit and swap the glass without touching the frame. This is the right call for a single isolated failure. If several units are failing across the same elevation, that’s a different conversation. Call (877) 558-4821 to get the exact quote.
The combination of grit from spring dust storms and UV-driven oxidation in the aluminum track. Grit works into the track and flat-spots the rollers, the track pits and oxidizes, and the sash starts to drag or jump the track. The fix is to pull the sash, replace the roller set and lock hardware, then clean and lubricate the track. If the track itself is bent or deeply pitted, replacing it is the honest answer. Call (877) 558-4821 for a free estimate.
Impact windows in this market are typically specified to meet local building code for high-wind zones, and the exact requirement depends on your specific opening and jurisdiction. An independent shop can service CGI impact-rated units: those are dual-pane laminated glass assemblies, and we service and re-seat them the same way we handle any impact-rated opening. Call (877) 558-4821 and we’ll walk through what your unit needs.
That depends on whether the failure is isolated or systemic. One fogged IGU on a twenty-year-old window is a glass job. A window wall of twenty-year-old CGI sashes all bowing, binding, and leaking air is a replacement conversation. We’ll price both options in writing so you can compare. Call (877) 558-4821 for a free estimate.
We quote per job, and the written estimate sets the final price. A glass-only IGU replacement runs less than a full window replacement, and hardware-only repairs run less than glass. Because the scope varies so widely – one sash versus a full window wall versus a full-frame install – we don’t publish a flat number. Call (877) 558-4821 for a free estimate and a written line-item quote.
Hardware repairs typically wrap up within a visit. Glass replacements depend on the IGU being measured and fabricated first, so they take longer from first call. Full-frame installs are scheduled around the scope. Every job we do starts with a written estimate that spells out the timeline. Call (877) 558-4821 to get that scheduled.
Book Your CGI Service in Enterprise, NV
If you own CGI windows or doors in Enterprise and something is fogging, dragging, or not sealing the way it should, get a real diagnostic before you decide anything. We provide independent CGI service, install, and repair with quality parts that fit your units, free estimates in writing, and honest repair-vs-replace guidance. Call (877) 558-4821. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Enterprise Windows & Doors.